路由器与串口通信问题

愤怒的狮子

我的路由器有视频返回，而且路由器开机时putty能收到下面这些信息，请大神们看看我的路由有没有问题， 我在控制软件上怎么按putty也收不到任何数据了，就开机时可以收到下面的数据。郁闷啊

愤怒的狮子

下面是putty收到的数据
Initialized Data:          0x8041DD30 - 0x8041FDC0 (8336)
BSS Area:                  0x8041FDC0 - 0x804265A0 (26592)
Local Heap:                0x804265A0 - 0x805265A0 (1048576)
Stack Area:                0x805265A0 - 0x805285A0 (8192)
Text (code) segment:       0x80401000 - 0x8041DD30 (118064)
Boot area (physical):      0x00529000 - 0x00569000
Relocation Factor:         I:00000000 - D:00000000

Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.159
Gateway IP address                :
Run from flash/host (f/h)         : h
Default host run file name        : 308nfs6358
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-9)                    : 96358VW2
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 00:14:d5:00:20:72
PSI Size (1-64) KBytes            : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number [0|1]          : 0

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe020000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.25 (openwrt@ampere) (gcc version 4.3.3 (GCC) ) #1 Fri Nov 19 21:51:29 PST 2010
Detected Broadcom 0x6358 CPU revision a1
CPU frequency is 300 MHz
32MB of RAM installed
registering 40 GPIOs
board_bcm963xx: CFE version: 1.0.37-10.3
bootconsole [early0] enabled
CPU revision is: 0002a010 (Broadcom BCM6358)
board_bcm963xx: board name: 96358VW2
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 29528k/32768k available (2140k kernel code, 3240k reserved, 453k data, 140k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 299.00 BogoMIPS (lpj=598016)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:01:1e.0: CardBus bridge, secondary bus 0000:02
pci 0000:01:1e.0:   IO window: 0x8008000-0x80080ff
pci 0000:01:1e.0:   IO window: 0x8008400-0x80084ff
pci 0000:01:1e.0:   MEM window: 0x38000000-0x3fffffff
PCI: Enabling device 0000:01:1e.0 (0000 -> 0003)
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.315:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  漏 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x02000000 at 0x1e000000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x00000001
CFI id  0x00002101
Amd/Fujitsu Extended Query Table at 0x0040
  Amd/Fujitsu Extended Query version 1.3.
bcm963xx: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96358VW2
bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset 100000 and length ee0000
bcm963xx_flash: Partition 3 is nvram offset fe0000 and length 20000
bcm963xx_flash: Partition 4 is linux offset 20000 and length fc0000
bcm963xx_flash: Spare partition is 400000 offset and length be0000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000020000 : "CFE"
0x000000020100-0x000000100000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x000000100000-0x000000fe0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
split_squashfs: no squashfs found in "bcm963xx"
0x000000fe0000-0x000001000000 : "nvram"
0x000000020000-0x000000fe0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: adsl
Registered led device: ppp-fail
Registered led device: power
Registered led device: stop
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (jffs2 filesystem) readonly on device 31:2.
Freeing unused kernel memory: 140k freed
Please be patient, while OpenWrt loads ...
-

愤怒的狮子

preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
- init -
bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (2)]
eth1: link forced UP - 100/full - flow control off/off
device eth1 entered promiscuous mode
br-lan: port 1(eth1) entering forwarding state
Compat-wireless backport release: compat-wireless-2010-10-14-7-gab01eca
Backport based on wireless-testing.git master-2010-10-19
cfg80211: Calling CRDA to update world regulatory domain
roboswitch: Probing device eth0: Failed to enable switch
roboswitch: Probing device eth1: found a 5325! It's a 5350.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
cfg80211: World regulatory domain updated:
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
usbcore: registered new device driver usb
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL, GPIO LED Mask: 0x000f, Firmware-ID: FW13 ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
nf_conntrack version 0.5.0 (463 buckets, 1852 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
uhci_hcd: USB Universal Host Controller Interface driver
i2c /dev entries driver
usb 2-1: new full speed USB device using bcm63xx_ohci and address 2
Linux video capture interface: v2.00
gspca: main v2.7.0 registered
usb 2-1: configuration #1 chosen from 1 choice
pwc: Philips webcam module version 10.0.13 loaded.
pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
usbcore: registered new interface driver Philips webcam
usbcore: registered new interface driver ov519
ov519: registered
gspca: probing 0ac8:301b
zc3xx: probe 2wr ov vga 0x0000
zc3xx: probe sensor -> 0011
zc3xx: Find Sensor HV7131R(c)
gspca: probe ok
usbcore: registered new interface driver zc3xx
zc3xx: registered
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
usbcore: deregistering interface driver ov519
ov519: deregistered
usbcore: registered new interface driver ov519
ov519: registered
zc3xx: probe 2wr ov vga 0x0000

愤怒的狮子

到底是哪里出了问题啊

liuviking

刷的固件是哪来的？ser2net安装了没？或者启动了没？

愤怒的狮子

liuviking 发表于 2012-7-17 23:19
刷的固件是哪来的？ser2net安装了没？或者启动了没？

在网上买的，代刷的，怎么看有没启动

liuviking

Putty里面输入ps回车，看看有没有ser2net这个项，一般网上代刷的都没有，如果没有可以刷论坛的固件，带有ser2net。

愤怒的狮子

liuviking 发表于 2012-7-18 00:18
Putty里面输入ps回车，看看有没有ser2net这个项，一般网上代刷的都没有，如果没有可以刷论坛的固件，带有se ...

能说下具体步骤吗，我很菜什么都不懂

愤怒的狮子

我输入了看到这些数据login as: root
root@192.168.1.1's password:


BusyBox v1.15.3 (2010-11-11 23:54:31 PST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

WIFI-ROBOT V1.2
______________________________________________________________________________
                                                                     o
#     # ### ##### ###    ####    ###  ####   ###  #####    __   _____|_   __
#  #  #  #  #      #     #   #  #   # #   # #   #   #     |  |_| ____| |_|  |
#  #  #  #  #####  # ### ####   #   # ####  #   #   #     |__| ||     || |__|
# # # #  #  #      #     #  #   #   # #   # #   #   #      __  ||_____||  __
#     # ### #     ###    #   #   ###  ####   ###    #     |  |_|       |_|  |
                                                          |__| |_o___o_| |__|
_______________________________________________________________________________
root@OpenWrt:~# ps
  PID USER       VSZ STAT COMMAND
    1 root      1368 S    init
    2 root         0 SW   [kthreadd]
    3 root         0 SW   [ksoftirqd/0]
    4 root         0 SW   [events/0]
    5 root         0 SW   [khelper]
    8 root         0 SW   [async/mgr]
   36 root         0 SW   [sync_supers]
   38 root         0 SW   [bdi-default]
   40 root         0 SW   [kblockd/0]
   70 root         0 SW   [kswapd0]
   71 root         0 SW   [aio/0]
   72 root         0 SW   [crypto/0]
   84 root         0 SW   [mtdblockd]
  223 root         0 SWN  [jffs2_gcd_mtd2]
  225 root      1360 S    /bin/sh /etc/init.d/rcS S boot
  227 root      1360 S    logger -s -p 6 -t sysinit
  240 root      1372 S    syslogd -C16
  242 root      1352 S    klogd
  256 root       780 S    /sbin/hotplug2 --override --persistent --set-worker /
  319 root      1364 S    udhcpc -t 0 -i eth0 -b -p /var/run/dhcp-eth0.pid -O r
  425 root         0 SW   [cfg80211]
  444 root         0 SW   [khubd]
  480 root         0 SW   [phy0]
  666 root         0 SW   [irq/39-b43]
  703 root      1460 S    hostapd -P /var/run/wifi-phy0.pid -B /var/run/hostapd
  804 root      1148 S    /usr/sbin/dropbear -p 22 -P /var/run/dropbear.1.pid
  813 root      1176 S    /usr/sbin/uhttpd -f -h /www -r OpenWrt -x /cgi-bin -t
  842 nobody     916 S    /usr/sbin/dnsmasq -K -D -y -Z -b -E -s lan -S /lan/ -
  858 root      3100 S    /usr/sbin/lighttpd -f /etc/lighttpd/lighttpd.conf
  860 root      5856 S    /usr/bin/php-fcgi
  866 root      1352 S    watchdog -t 5 /dev/watchdog
  869 root      5856 S    /usr/bin/php-fcgi
  877 root      1204 S    /usr/sbin/dropbear -p 22 -P /var/run/dropbear.1.pid
  878 root      1368 S    -ash
  883 root      1360 R    ps
root@OpenWrt:~# root@OpenWrt:~# ps
-ash: root@OpenWrt:~#: not found
root@OpenWrt:~#   PID USER       VSZ STAT COMMAND
-ash: PID: not found
root@OpenWrt:~#     1 root      1368 S    init
-ash: 1: not found
root@OpenWrt:~#     2 root         0 SW   [kthreadd]
-ash: 2: not found
root@OpenWrt:~#     3 root         0 SW   [ksoftirqd/0]
-ash: 3: not found
root@OpenWrt:~#     4 root         0 SW   [events/0]
-ash: 4: not found
root@OpenWrt:~#     5 root         0 SW   [khelper]
-ash: 5: not found
root@OpenWrt:~#     8 root         0 SW   [async/mgr]
-ash: 8: not found
root@OpenWrt:~#    36 root         0 SW   [sync_supers]
-ash: 36: not found
root@OpenWrt:~#    38 root         0 SW   [bdi-default]
-ash: 38: not found
root@OpenWrt:~#    40 root         0 SW   [kblockd/0]
-ash: 40: not found
root@OpenWrt:~#    70 root         0 SW   [kswapd0]
-ash: 70: not found
root@OpenWrt:~#    71 root         0 SW   [aio/0]
-ash: 71: not found
root@OpenWrt:~#    72 root         0 SW   [crypto/0]
-ash: 72: not found
root@OpenWrt:~#    84 root         0 SW   [mtdblockd]
-ash  225 root      1360 S    /bin/sh /etc/init.d/rcS S boot
: 84: not found
root@OpenWrt:~#   223 root         0 SWN  [jffs2_gcd_mtd2]
-ash: 223: not found
root@OpenWrt:~#   225 root      1360 S    /bin/sh /etc/init.d/rcS S boot
-ash: 225: not found
root@OpenWrt:~#   227 root      1360 S    logger -s -p 6 -t sysinit
-ash: 227: not found
root@OpenWrt:~#   240 root      1372 S    syslogd -C16
  703 root      1460 S    hostapd -P /var/run/wifi-phy0.pid -B /var/run/hostapd
-ash: 240: not found
root@OpenWrt:~#   242 root      1352 S    klogd
-ash: 242: not found
root@OpenWrt:~#   256 root       780 S    /sbin/hotplug2 --override --persistent
--set-worker /
-ash: 256: not found
root@OpenWrt:~#   319 root      1364 S    udhcpc -t 0 -i eth0 -b -p /var/run/dhc
p-eth0.pid -O r
-ash: 319: not found
root@OpenWrt:~#   425 root         0 SW   [cfg80211]
-ash: 425: not found
root@OpenWrt:~#   444 root         0 SW   [khubd]
-ash: 444: not found
root@OpenWrt:~#   480 root         0 SW   [phy0]
-ash: 480: not found
root@OpenWrt:~#   666 root         0 SW   [irq/39-b43]
-ash: 666: not found
root@OpenWrt:~#   703 root      1460 S    hostapd -P /var/run/wifi-phy0.pid -B /
var/run/hostapd
-ash: 703: not found
root@OpenWrt:~#   804 root      1148 S    /usr/sbin/dropbear -p 22 -P /var/run/d
ropbear.1.pid
-ash: 804: not found
root@OpenWrt:~#   813 root      1176 S    /usr/sbin/uhttpd -f -h /www -r OpenWrt
-x /cgi-bin -t
-ash: 813: not found
root@OpenWrt:~#   842 nobody     916 S    /usr/sbin/dnsmasq -K -D -y -Z -b -E -s
lan -S /lan/ -
-ash: 842: not found
root@OpenWrt:~#   858 root      3100 S    /usr/sbin/lighttpd -f /etc/lighttpd/li
ghttpd.conf
-ash: 858: not found
root@OpenWrt:~#   860 root      5856 S    /usr/bin/php-fcgi
-ash: 860: not found
root@OpenWrt:~#   866 root      1352 S    watchdog -t 5 /dev/watchdog
-ash: 866: not found
root@OpenWrt:~#   869 root      5856 S    /usr/bin/php-fcgi
-ash: 869: not found
root@OpenWrt:~#   877 root      1204 S    /usr/sbin/dropbear -p 22 -P /var/run/d
ropbear.1.pid
-ash: 877: not found
root@OpenWrt:~#   878 root      1368 S    -ash
-ash: 878: not found
root@OpenWrt:~#   883 root      1360 R    ps
-ash: 883: not found
root@OpenWrt:~# root@OpenWrt:~#
-ash: root@OpenWrt:~#: not found
root@OpenWrt:~#

liuviking

愤怒的狮子 发表于 2012-7-18 17:56
我输入了看到这些数据login as: root
's password:

没有ser2net，说明就是没有安装的。