求助啊。。。刚玩一会的703不知道怎么的就上电之后一直闪灯。。。启动不了？

Thun

具体情况就是      上电。。然后亮一下，等10秒吧大概。然后开始一直闪灯。。。一直闪一直闪。。。。是不是烧了。。= =还是什么坏掉了。。。是用哪种方法能救回来呢》？。。、
能用usb-ttl 刷么。。。。教程没看很明白。。。= =还有教程里下载的那个tftpd32是干嘛用的。。教程里打开了就没他的操作了啊= =小白一只。。弱弱求教了。。。

liuviking

明显系统挂掉了啊，可以看看我们论坛的教程，重刷固件。

Thun

liuviking 发表于 2013-7-21 00:05
明显系统挂掉了啊，可以看看我们论坛的教程，重刷固件。

是那个救砖的教程么。。。。有点没看明白。。那个tftpd32是干嘛用的。。教程里打开了就没他的操作了啊= =

AbCdEfG

用USB供电了？

Thun

插本上的。。。。之前还行啊。。。。不知道怎么滴突然就挂了

Thun

liuviking 发表于 2013-7-21 00:05
明显系统挂掉了啊，可以看看我们论坛的教程，重刷固件。

是用救砖的办法么。。。。先还原。。再。先刷factory，然后sysupgrade？

liuviking

Thun 发表于 2013-7-21 14:25
是用救砖的办法么。。。。先还原。。再。先刷factory，然后sysupgrade？

有的，我们论坛不是有很多TTL救砖的教程吗？按那个教程刷好后，无需再刷即可。

Thun

liuviking 发表于 2013-7-21 15:54
有的，我们论坛不是有很多TTL救砖的教程吗？按那个教程刷好后，无需再刷即可。

现在是这样求解。。。。。



U-Boot 1.1.4 (May  3 2012 - 22:04:42)

AP121 (ar9330) U-boot

DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 8388608, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 3 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.3.8 (liuviking@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #3 Sat Jun 30 09:34:30 PDT 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61792k/65536k available (2075k kernel code, 3744k reserved, 395k data, 200k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:48
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-WR703N v1
[    0.340000] bio: create slab <bio-0> at 0
[    0.340000] Switching to clocksource MIPS
[    0.350000] NET: Registered protocol family 2
[    0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.360000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.370000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.370000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.380000] TCP reno registered
[    0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.390000] NET: Registered protocol family 1
[    0.420000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.430000] msgmni has been set to 120
[    0.430000] io scheduler noop registered
[    0.440000] io scheduler deadline registered (default)
[    0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.450000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.470000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    0.470000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    0.480000] 5 tp-link partitions found on MTD device spi0.0
[    0.480000] Creating 5 MTD partitions on "spi0.0":
[    0.490000] 0x000000000000-0x000000020000 : "u-boot"
[    0.490000] 0x000000020000-0x0000000fc7c0 : "kernel"
[    0.500000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.510000] 0x0000000fc7c0-0x0000007f0000 : "rootfs"
[    0.520000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.530000] mtd: partition "rootfs" set to be root filesystem
[    0.530000] mtd: partition "rootfs_data" created automatically, ofs=370000, len=480000
[    0.540000] 0x000000370000-0x0000007f0000 : "rootfs_data"
[    0.550000] 0x0000007f0000-0x000000800000 : "art"
[    0.550000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.800000] ag71xx_mdio: probed
[    0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.410000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.410000] TCP westwood registered
[    1.420000] NET: Registered protocol family 17
[    1.420000] 8021q: 802.1Q VLAN Support v1.8
[    1.430000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.440000] Freeing unused kernel memory: 200k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    6.780000] eth0: link up (100Mbps/Full duplex)
[    6.790000] JFFS2 notice: (408) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 13 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -
[    6.910000] Kernel panic - not syncing: Attempted to kill init!

liuviking

Thun 发表于 2013-7-22 22:10
现在是这样求解。。。。。

内核混乱了，你换一个固件刷一下

dgtutu

淘宝有一种ttl线是可以的