703N TTL 救砖求助附CRT码

281471299 · 发表于 2014-3-18 12:27:32

按照步骤刷的刷完还是不能连接

等高手帮忙

U-Boot 1.1.4 (Dec  4 2012 - 11:19:40)

AP121 (ar9330) U-boot

DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
hornet> setenv serverip 192.168.1.2
hornet> setenv ipaddr 192.168.1.1
hornet> tftp 0x80000000 wr703nv1.bin
dup 1 speed 1000
Using eth1 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'wr703nv1.bin'.
Load address: 0x80000000
Loading: #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      ######################################################
done
Bytes transferred = 3932160 (3c0000 hex)
hornet>

U-Boot 1.1.4 (Dec  4 2012 - 11:19:40)

AP121 (ar9330) U-boot

DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.2.12 (liuviking@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun May 20 09:54:32 PDT 2012
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000]  memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000]    0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[ 0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61804k/65536k available (2055k kernel code, 3732k reserved, 392k data, 192k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:48
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is TP-LINK TL-WR703N v1
[ 0.330000] bio: create slab <bio-0> at 0
[ 0.340000] Switching to clocksource MIPS
[ 0.350000] NET: Registered protocol family 2
[ 0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.350000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.360000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.360000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.370000] TCP reno registered
[ 0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] NET: Registered protocol family 1
[ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.410000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.420000] msgmni has been set to 120
[ 0.430000] io scheduler noop registered
[ 0.430000] io scheduler deadline registered (default)
[ 0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.440000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.450000] console [ttyATH0] enabled, bootconsole disabled
[ 0.450000] console [ttyATH0] enabled, bootconsole disabled
[ 0.460000] m25p80 spi0.0: found en25q32b, expected m25p80
[ 0.470000] m25p80 spi0.0: en25q32b (4096 Kbytes)
[ 0.470000] 5 tp-link partitions found on MTD device spi0.0
[ 0.480000] Creating 5 MTD partitions on "spi0.0":
[ 0.480000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.490000] 0x000000020000-0x0000000fa370 : "kernel"
[ 0.490000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.510000] 0x0000000fa370-0x0000003f0000 : "rootfs"
[ 0.510000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.520000] mtd: partition "rootfs" set to be root filesystem
[ 0.530000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=B0000
[ 0.540000] 0x000000340000-0x0000003f0000 : "rootfs_data"
[ 0.540000] 0x0000003f0000-0x000000400000 : "art"
[ 0.550000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.800000] ag71xx_mdio: probed
[ 0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.410000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 1.410000] TCP westwood registered
[ 1.420000] NET: Registered protocol family 17
[ 1.420000] 8021q: 802.1Q VLAN Support v1.8
[ 1.440000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.450000] Freeing unused kernel memory: 192k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 8.840000] JFFS2 notice: (402) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 13 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -
[ 9.070000] Kernel panic - not syncing: Attempted to kill init!

281471299 · 发表于 2014-3-18 12:30:59

按照步骤刷的刷完还是不能连接

等高手帮忙

U-Boot 1.1.4 (Dec  4 2012 - 11:19:40)

AP121 (ar9330) U-boot

DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
hornet> setenv serverip 192.168.1.2
hornet> setenv ipaddr 192.168.1.1
hornet> tftp 0x80000000 wr703nv1.bin
dup 1 speed 1000
Using eth1 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'wr703nv1.bin'.
Load address: 0x80000000
Loading: #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      #################################################################
      ######################################################
done
Bytes transferred = 3932160 (3c0000 hex)
hornet>

下面是重新启动的CRT代码

U-Boot 1.1.4 (Dec  4 2012 - 11:19:40)

AP121 (ar9330) U-boot

DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.2.12 (liuviking@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun May 20 09:54:32 PDT 2012
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000]  memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000]    0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[ 0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61804k/65536k available (2055k kernel code, 3732k reserved, 392k data, 192k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:48
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is TP-LINK TL-WR703N v1
[ 0.330000] bio: create slab <bio-0> at 0
[ 0.340000] Switching to clocksource MIPS
[ 0.350000] NET: Registered protocol family 2
[ 0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.350000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.360000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.360000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.370000] TCP reno registered
[ 0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] NET: Registered protocol family 1
[ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.410000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.420000] msgmni has been set to 120
[ 0.430000] io scheduler noop registered
[ 0.430000] io scheduler deadline registered (default)
[ 0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.440000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.450000] console [ttyATH0] enabled, bootconsole disabled
[ 0.450000] console [ttyATH0] enabled, bootconsole disabled
[ 0.460000] m25p80 spi0.0: found en25q32b, expected m25p80
[ 0.470000] m25p80 spi0.0: en25q32b (4096 Kbytes)
[ 0.470000] 5 tp-link partitions found on MTD device spi0.0
[ 0.480000] Creating 5 MTD partitions on "spi0.0":
[ 0.480000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.490000] 0x000000020000-0x0000000fa370 : "kernel"
[ 0.490000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.510000] 0x0000000fa370-0x0000003f0000 : "rootfs"
[ 0.510000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.520000] mtd: partition "rootfs" set to be root filesystem
[ 0.530000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=B0000
[ 0.540000] 0x000000340000-0x0000003f0000 : "rootfs_data"
[ 0.540000] 0x0000003f0000-0x000000400000 : "art"
[ 0.550000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.800000] ag71xx_mdio: probed
[ 0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.410000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 1.410000] TCP westwood registered
[ 1.420000] NET: Registered protocol family 17
[ 1.420000] 8021q: 802.1Q VLAN Support v1.8
[ 1.440000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.450000] Freeing unused kernel memory: 192k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 8.840000] JFFS2 notice: (402) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 13 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -
[ 9.070000] Kernel panic - not syncing: Attempted to kill init!