703N V1.7怎么都刷不了OP

小黄豆

高手帮忙呀，网上买了个TL的703N，想自己刷OP，收到货一看，硬件版本V1.7的，网线刷不了OP，提示版本与机型不符，改用TTL+网线，还是刷不了，上电3秒内按空格键完全无效，接线没问题，因为能通信上，不知哪位高手能看懂是什么问题吗
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.02.09 20:14:49 =~=~=~=~=~=~=~=~=~=~=~=


U-Boot 1.1.4-gd0be0bfd (Jan 20 2014 - 15:34:33)

AP121 (ar9330) U-boot

DRAM:  32 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

Booting AR9330(Hornet)...

Linux version 2.6.31--LSDK-9.2.0.312 (jenkins@git-server) (gcc version 4.3.3 (GCC) ) #1 Mon Jan 20 15:37:32 CST 2014

flash_size passed from bootloader = 4

CPU revision is: 00019374 (MIPS 24Kc)

Determined physical RAM map:

memory: 02000000 @ 00000000 (usable)

User-defined physical RAM map:

memory: 02000000 @ 00000000 (usable)

Zone PFN ranges:

  Normal   0x00000000 -> 0x00002000

Movable zone start PFN for each node

early_node_map[1] active PFN ranges

    0: 0x00000000 -> 0x00002000

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128

Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ar7240-nor0:128k(u-boot),1024k(kernel),2816(rootfs),64k(config),64k(ART) mem=32M

PID hash table entries: 128 (order: 7, 512 bytes)

Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.

Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes

Writing ErrCtl register=00000000

Readback ErrCtl register=00000000

Memory: 29876k/32768k available (1883k kernel code, 2892k reserved, 521k data, 116k init, 0k highmem)

Hierarchical RCU implementation.

NR_IRQS:128

plat_time_init: plat time init done

Calibrating delay loop... 266.24 BogoMIPS (lpj=532480)

Mount-cache hash table entries: 512

NET: Registered protocol family 16

===== ar7240_platform_init: 0



Whoops! This kernel is for product wr703 v1.0!


bio: create slab <bio-0> at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 1024 (order: 1, 8192 bytes)

TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

TCP: Hash tables configured (established 1024 bind 1024)

TCP reno registered

NET: Registered protocol family 1

AR7240 GPIOC major 0

squashfs: version 4.0 (2009/01/31) Phillip Lougher

NTFS driver 2.1.29 [Flags: R/O].

msgmni has been set to 58

alg: No test for lzma (lzma-generic)

alg: No test for stdrng (krng)

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered (default)

Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled

ttyS0: detected caps 00000000 should be 00000100

serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A

console [ttyS0] enabled

PPP generic driver version 2.4.2

NET: Registered protocol family 24

cmdlinepart partition parsing not available

set partition boot

set partition kernel

set partition rootfs

set partition config

set partition art

set partition

liuviking

貌似uboot都和1.6不一样了，你得找到进入uboot的命令才行

nsp

进来学习一下  拿 个金币

chuifenglaodaye

与楼主一块学习

小黄豆

chuifenglaodaye 发表于 2015-2-10 11:30
与楼主一块学习

已经解决了，还是采用TTL+网线的办法，用TPL命令+tftpd32刷好了