|
|
楼主 |
发表于 2015-8-10 15:31:46
|
显示全部楼层
这个是完整的！
U-Boot 1.1.3 (Oct 9 2013 - 21:17:42)
Board: Ralink APSoC DRAM: 32 MB
relocate_code Pointer at: 81fb4000
spi_wait_nsec: 42
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:30000 len:1000
.*** W
arning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.6.0.0
--------------------------------------------
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flas
h component: SPI Flash
Date:Oct 9 2013 Time:21:17:42
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 360 MHZ ####
estimate memory size =32 Mbytes
Please choose the operation:
1: Load system code t
o SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
4
3
2
1
0
3
: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
. Image Name: Linux Kernel Image
Created: 2014-04-17 18:06:31 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 983586 Bytes = 960.5 kB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:500
40 len:f0222
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. Verifying Checksum ... OK
Uncompressi
ng Kernel Image ...
OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32
Starting kernel ...
[ 0.000000] Linux version 3.10.34 (liuviking@ubuntu) (gcc version 4.8.3 (OpenWrt/Lina
ro GCC 4.8-2014.01 r40400) ) #11 Thu Apr 17 11:05:41 PDT 2014
[ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[ 0.000000] MIPS: machine is HAME MPR-A2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[
0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cac
he 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 51
2 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=000006a0
[ 0.000000] Readback ErrCtl register=000006a0
[ 0.000000] Memory: 29352k/32768k available (2136k kernel code,
3416k reserved, 548k data, 192k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 360MHz
[ 0.000000] Calibrating delay loop...
239.61 BogoMIPS (lpj=1198080)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-
cache hash table entries: 512
[ 0.080000] pinctrl core: initialized pinctrl subsystem
[ 0.090000] NET: Registered protocol family 16
[ 0.110000] rt2880-pinmux pinctrl.1: invalid group "rgmii" for function "gpio"
[ 0.120000] r
t2880-pinmux pinctrl.1: invalid group "mdio" for function "gpio"
[ 0.150000] bio: create slab <bio-0> at 0
[ 0.160000] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.170000] rt2
880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.180000] Switching to clocksource MIPS
[ 0.190000] NET: Registered protocol family 2
[ 0.200000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.220000] TCP bind hash tab
le entries: 512 (order: -1, 2048 bytes)
[ 0.230000] TCP: Hash tables configured (established 512 bind 512)
[ 0.240000] TCP: reno registered
[ 0.250000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.260000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.270000] NET: Registered protocol family 1
[ 0.28000
0] rt-timer 10000100.timer: maximum frequncy is 7324Hz
[ 0.330000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.340000
] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.370000] msgmni has been set to 57
[ 0.380000] io scheduler noop registered
[ 0.380000] io scheduler deadline registered (default)
[ 0.400000] gpio-export gpio_export.6: 2 gpio(s) exported
[ 0.4
10000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.430000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 0.440000] console [ttyS0] enabled, bootconsole disabled
[ 0.440000] console [ttyS0] enabled, bootconsole disabled
[
0.470000] m25p80 spi32766.0: s25fl064k (8192 Kbytes)
[ 0.480000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.490000] Creating 4 MTD partitions on "spi32766.0":
[ 0.500000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.520000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.5300
00] 0x000000040000-0x000000050000 : "factory"
[ 0.550000] 0x000000050000-0x000000800000 : "firmware"
[ 0.560000] 0x000000140262-0x000000800000 : "rootfs"
[ 0.570000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.600000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.610000] mtd: partition "rootfs_data" created automatically, ofs=0x3c0000, len=0x440000
[ 0.630000] 0x0000003c0000-0x000000800000 : "rootfs_data"
[ 0.650000] eth0: done loading
[ 0.660000] rt3xxx-usbphy ubsphy.3: loaded
[ 0.670000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.680000] TCP: cubic registered
[ 0.690000] NET: Registered protocol family 17
[ 0.700000] 8021q: 802.1Q VLAN Support v1.8
[ 0.730000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.750000] Freeing unused kernel memory: 192K (802a0000 - 802d0000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
[ 7.670000] rt305x-esw 10110000.esw: link changed 0x00
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2
], [3] or [4] key and hit [enter] to select the debug level
[ 8.850000] usbcore: registered new interface driver usbfs
[ 8.860000] usbcore: registered new interface driver hub
[ 8.870000] usbcore: registered new device driver usb
[ 8.890000] ehci_hcd: USB 2.0 'Enhanced' Host
Controller (EHCI) Driver
[ 8.910000] ehci-platform: EHCI generic platform driver
[ 9.120000] rt3xxx-usbphy ubsphy.3: remote usb device wakeup disabled
[ 9.130000] rt3xxx-usbphy ubsphy.3: UTMI 16bit 30MHz
[ 9.140000] ehci-platform 101c0000.ehci: EHCI
Host Controller
[ 9.160000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 9.170000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 9.200000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 9.210000] hub 1-0:1.0
: USB hub found
[ 9.220000] hub 1-0:1.0: 1 port detected
[ 9.230000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.240000] ohci-platform 101c1000.ohci: Generic Platform OHCI Controller
[ 9.260000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 9.270000] ohci-pla
tform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 9.350000] hub 2-0:1.0: USB hub found
[ 9.360000] hub 2-0:1.0: 1 port detected
[ 9.370000] leds-gpio gpio-leds.4: pins are not configured from the driver
jffs2 is ready
[ 11.620000] jffs2: notice: (289) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
switching to jffs2
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Command failed: Not found
[ 16.460000] NET: Registered protocol family 10
[ 16.490000] nf_conntrack version 0.5.0 (461 buckets, 1844 max)
[ 16.510000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 16.560000] L
inux video capture interface: v2.00
[ 16.590000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2
[ 16.610000] Backport generated by backports.git backports-20140221-0-g8e94650
[ 16.640000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.710000] usbcore: registered new interface driver uvcvideo
[ 16.720000] USB Video Class driver (1.1.1)
[ 16.760000] xt_time: kernel timezone is -0000
[ 1
6.820000] cfg80211: Calling CRDA to update world regulatory domain
[ 16.880000] cfg8
0211: World regulatory domain updated:
[ 16.890000] cfg80211: DFS Master region: unset
[ 16.890000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 16.910000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.930000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz
), (N/A, 2000 mBm), (N/A)
[ 16.950000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.960000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.980000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.990000] cfg80211: (57240000 KHz - 63720000 KHz
@ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 17.050000] PPP generic driver version 2.4.2
[ 17.070000] NET: Registered protocol family 24
[
17.130000] rt2800_wmac 10180000.wmac: failed to load eeprom property
[ 17.140000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[ 17.160000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
[ 17.180000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 53
50 detected
[ 27.750000] device eth0.1 entered promiscuous mode
[ 27.760000] device eth0 entered promiscuous mode
[ 27.790000] br-lan: port 1(eth0.1) entered forwarding state
[ 27.800000] br-l
an: port 1(eth0.1) entered forwarding state
[ 28.820000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
procd: - init complete -
[ 29.80000
0] br-lan: port 1(eth0.1) entered forwarding state
[ 31.210000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 31.230000] device wlan0 entered p
romiscuous mode
[ 31.280000] br-lan: port 2(wlan0) entered forwarding state
[ 31.290000] br-lan: port 2(wlan0) entered forwa
rding state
[ 31.300000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 33.290000] br-lan: port 2(wlan0) ent
ered forwarding state
|
|
/2 
|QQ技术咨询1|QQ技术咨询2|商务合作微信1：xiaorgeek001|商务合作微信2:XiaoRGEEK|诚聘英才|Archiver|手机版|小R科技-WIFI机器人网·机器人创意工作室
( 粤ICP备15000788号-6 )
发表于 2015-8-10 15:00:51
