小R科技-WIFI机器人网·机器人创意工作室

 找回密码
 立即注册
查看: 2873|回复: 3

703N TTL 救砖 求助 附CRT码

[复制链接]
发表于 2014-3-18 12:27:32 | 显示全部楼层 |阅读模式
按照步骤刷的 刷完还是不能连接

等高手帮忙

U-Boot 1.1.4 (Dec  4 2012 - 11:19:40)

AP121 (ar9330) U-boot

DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
hornet> setenv serverip 192.168.1.2
hornet> setenv ipaddr 192.168.1.1
hornet> tftp 0x80000000 wr703nv1.bin
dup 1 speed 1000
Using eth1 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'wr703nv1.bin'.
Load address: 0x80000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ######################################################
done
Bytes transferred = 3932160 (3c0000 hex)
hornet>



U-Boot 1.1.4 (Dec  4 2012 - 11:19:40)

AP121 (ar9330) U-boot

DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.2.12 (liuviking@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun May 20 09:54:32 PDT 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61804k/65536k available (2055k kernel code, 3732k reserved, 392k data, 192k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:48
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is TP-LINK TL-WR703N v1
[    0.330000] bio: create slab <bio-0> at 0
[    0.340000] Switching to clocksource MIPS
[    0.350000] NET: Registered protocol family 2
[    0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.350000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.360000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.360000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.370000] TCP reno registered
[    0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.380000] NET: Registered protocol family 1
[    0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.410000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.420000] msgmni has been set to 120
[    0.430000] io scheduler noop registered
[    0.430000] io scheduler deadline registered (default)
[    0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.440000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.460000] m25p80 spi0.0: found en25q32b, expected m25p80
[    0.470000] m25p80 spi0.0: en25q32b (4096 Kbytes)
[    0.470000] 5 tp-link partitions found on MTD device spi0.0
[    0.480000] Creating 5 MTD partitions on "spi0.0":
[    0.480000] 0x000000000000-0x000000020000 : "u-boot"
[    0.490000] 0x000000020000-0x0000000fa370 : "kernel"
[    0.490000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.510000] 0x0000000fa370-0x0000003f0000 : "rootfs"
[    0.510000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.520000] mtd: partition "rootfs" set to be root filesystem
[    0.530000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=B0000
[    0.540000] 0x000000340000-0x0000003f0000 : "rootfs_data"
[    0.540000] 0x0000003f0000-0x000000400000 : "art"
[    0.550000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.800000] ag71xx_mdio: probed
[    0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.410000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.410000] TCP westwood registered
[    1.420000] NET: Registered protocol family 17
[    1.420000] 8021q: 802.1Q VLAN Support v1.8
[    1.440000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.450000] Freeing unused kernel memory: 192k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    8.840000] JFFS2 notice: (402) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 13 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -
[    9.070000] Kernel panic - not syncing: Attempted to kill init!

回复

使用道具 举报

 楼主| 发表于 2014-3-18 12:30:59 | 显示全部楼层

703N TTL 救砖求助 附CRT代码 等高手帮忙啊!!!

按照步骤刷的 刷完还是不能连接

等高手帮忙

U-Boot 1.1.4 (Dec  4 2012 - 11:19:40)

AP121 (ar9330) U-boot

DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
hornet> setenv serverip 192.168.1.2
hornet> setenv ipaddr 192.168.1.1
hornet> tftp 0x80000000 wr703nv1.bin
dup 1 speed 1000
Using eth1 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'wr703nv1.bin'.
Load address: 0x80000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ######################################################
done
Bytes transferred = 3932160 (3c0000 hex)
hornet>



下面是重新启动的CRT代码

U-Boot 1.1.4 (Dec  4 2012 - 11:19:40)

AP121 (ar9330) U-boot

DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.2.12 (liuviking@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun May 20 09:54:32 PDT 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61804k/65536k available (2055k kernel code, 3732k reserved, 392k data, 192k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:48
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is TP-LINK TL-WR703N v1
[    0.330000] bio: create slab <bio-0> at 0
[    0.340000] Switching to clocksource MIPS
[    0.350000] NET: Registered protocol family 2
[    0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.350000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.360000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.360000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.370000] TCP reno registered
[    0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.380000] NET: Registered protocol family 1
[    0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.410000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.420000] msgmni has been set to 120
[    0.430000] io scheduler noop registered
[    0.430000] io scheduler deadline registered (default)
[    0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.440000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.460000] m25p80 spi0.0: found en25q32b, expected m25p80
[    0.470000] m25p80 spi0.0: en25q32b (4096 Kbytes)
[    0.470000] 5 tp-link partitions found on MTD device spi0.0
[    0.480000] Creating 5 MTD partitions on "spi0.0":
[    0.480000] 0x000000000000-0x000000020000 : "u-boot"
[    0.490000] 0x000000020000-0x0000000fa370 : "kernel"
[    0.490000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.510000] 0x0000000fa370-0x0000003f0000 : "rootfs"
[    0.510000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.520000] mtd: partition "rootfs" set to be root filesystem
[    0.530000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=B0000
[    0.540000] 0x000000340000-0x0000003f0000 : "rootfs_data"
[    0.540000] 0x0000003f0000-0x000000400000 : "art"
[    0.550000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.800000] ag71xx_mdio: probed
[    0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.410000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.410000] TCP westwood registered
[    1.420000] NET: Registered protocol family 17
[    1.420000] 8021q: 802.1Q VLAN Support v1.8
[    1.440000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.450000] Freeing unused kernel memory: 192k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    8.840000] JFFS2 notice: (402) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 13 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -
[    9.070000] Kernel panic - not syncing: Attempted to kill init!
回复 支持 反对

使用道具 举报

发表于 2014-3-19 09:22:17 | 显示全部楼层
固件可能有问题,换一个试试。
回复 支持 反对

使用道具 举报

发表于 2015-2-7 21:51:02 | 显示全部楼层
进来学习学习  看看地
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

新品特惠推荐上一条 /2 下一条

QQ|QQ技术咨询1|QQ技术咨询2|商务合作微信1:xiaorgeek001|商务合作微信2:XiaoRGEEK|诚聘英才|Archiver|手机版|小R科技-WIFI机器人网·机器人创意工作室 ( 粤ICP备15000788号-6 )

GMT+8, 2024-11-22 23:48 , Processed in 1.083946 second(s), 18 queries .

Powered by XiaoR GEEK X3.4

© 2014-2021 XiaoR GEEK

快速回复 返回顶部 返回列表